Contact us MX +52 (867) 715-5016

Accumulation Conveyors

796 Accumulator Line Shaft Zero Pressure Conveyor (796LSZ)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S; same BF as conveyor up to 39" BF; units 43" BF and above, rollers are 21" BF with STANDARD 12" wide belt; 27" BF if OPTIONAL 24" belt is used.BELTING: 12" wide PVC-120.RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196SCENTER DRIVE: Reversible drive with 24" integral belt take-up. For units under 8'-0" overall length, drive components must be stacked.END PULLEY: 4" dia. with 1-3/16" dia. shaft on 15"-39" BF; 6" dia. with 1-7/16" dia. shaft above 39" BF; both crowned.DRIVE PULLEY: 8" dia. with 1-7/16" dia. shaft on 15"-39" BF; 12" dia. with 1-15/16" dia. shaft above 39" BF; both crowned and fully lagged.SPEED: 35 FPM, constant.BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.BED: 7" x 1-1/2" x 10 ga. formed steel channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.MOTOR DRIVE: 1 HP, 230/460/3, 60 cycle, ODP right angle gear motor.FLOOR SUPPORTS: 8" and 12" center drive (with 4" or 6"end pulley) adjustable 33" to 36" TOR with SH-6 at end plates and SH-7 at intermediates. Supports provided on 5' centers and should be lagged to floor.ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. '

796 Accumulator Smart Zone Line Shaft Zero Pressure Conveyor (SZ796LSZ)

' TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). CENTER DRIVE: Located approximately 16-1/2" from end of bed section on 4" RC; 18" on 3" and 6" RC. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. ACCUMULATION: Zone singulation operation; 2'-0" zone length, photoeye controlled. SPEED: 60 FPM, constant. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional'

251 Accumulator SZ Chain Driven Zero Pressure Heavy Duty Conveyor (SZD251CDA)

' TREAD ROLLERS: 2.5 " dia. x 11 ga., model 251S. CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain. CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor. CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units. ROLLER CENTERS: 4" or 6" RC ONLY. SPEED: 35 FPM, constant. ACCUMULATION ZONE: 5'-0" zone lengths, zone singulation operation, photo electric sensor controlled zones with seperate drives on each zone. BED: 7-1/2" x 1-1/2" x 7 ga. and 5 " x 1-1/2" x 7 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports. FLOOR SUPPORTS: Optional BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal. FRL: Unit is provided with filter, regulator and lubricator with 3/8" ports for 60 PSI operational pressure. MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor CAPACITY: 1000 lbs./ft. up to a maximum of 3000 lb. pallet load.'

251 Accumulator SZ Chain Driven Zero Pressure Heavy Duty Conveyor (SZA251CDA)

' TREAD ROLLERS: 2.5 " dia. x 11 ga., model 251S. CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain. CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor. CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units. ROLLER CENTERS: 4" or 6" RC ONLY. SPEED: 35 FPM, constant. ACCUMULATION ZONE: 5'-0" zone lengths, zone singulation operation, photo electric sensor controlled zones with seperate drives on each zone. BED: 7-1/2" x 1-1/2" x 7 ga. and 5 " x 1-1/2" x 7 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports. FLOOR SUPPORTS: Optional BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal. FRL: Unit is provided with filter, regulator and lubricator with 3/8" ports for 60 PSI operational pressure. MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor CAPACITY: 1000 lbs./ft. up to a maximum of 3000 lb. pallet load.'

192 Accumulator SZ Chain Driven Zero Pressure Medium Duty Conveyor (SZD192CDA)

' TREAD ROLLERS: 1.9" dia. x 12 ga., model 192S. CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain. CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor. CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units. ROLLER CENTERS: 4" or 6" RC ONLY. SPEED: 35 FPM, constant. ACCUMULATION ZONE: 5'-0" zone lengths, zone singulation operation, photo electric sensor controlled zones with seperate drives on each zone. BED: 6-1/2" x 1-1/2" x 10 ga. and 4-1/2" x 1-1/2" x 10 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports. FLOOR SUPPORTS: Optional BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal. FRL: Unit is provided with filter, regulator and lubricator with 3/8" ports for 60 PSI operational pressure. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. CAPACITY: 300 lbs./ft. up to a maximum of 1200 lb. pallet load.'

192 Accumulator SZ Chain Driven Zero Pressure Medium Duty Conveyor (SZD192CDA)

' TREAD ROLLERS: 1.9" dia. x 12 ga., model 192S. CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain. CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor. CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units. ROLLER CENTERS: 4" or 6" RC ONLY. SPEED: 35 FPM, constant. ACCUMULATION ZONE: 5'-0" zone lengths, zone singulation operation, photo electric sensor controlled zones with seperate drives on each zone. BED: 6-1/2" x 1-1/2" x 10 ga. and 4-1/2" x 1-1/2" x 10 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports. FLOOR SUPPORTS: Optional BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal. FRL: Unit is provided with filter, regulator and lubricator with 3/8" ports for 60 PSI operational pressure. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. CAPACITY: 300 lbs./ft. up to a maximum of 1200 lb. pallet load.'

196 Accumulator Smart Zone Zero Pressure Medium Duty Conveyor (SZ196ZPA)

' TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S; 8" BF with 6" wide belt. RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6" wide black PVC-120 COS. DRIVE PULLEY: 4" dia. with 1-3/16" dia. shaft or 8" dia. with 1-7/16" dia. shaft; both crowned and fully lagged. END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7" x 1-1/2" x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30'.li> FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: Zone singulation operation; 3" RC = 2'-0" long zones; 4-1/2" RC = 3'-0" long zones. 1'-0" of live roller at each end of conveyor over end plates remains "live" during operation. Zones are pneumatically actuated using p'

196 Accumulator Zero Pressure Medium Duty Conveyor (196ZPA)

' TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S; 8" BF with 6" wide belt. RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6" wide black PVC-120 COS. DRIVE PULLEY: 4" dia. with 1-3/16" dia. shaft or 8" dia. with 1-7/16" dia. shaft; both crowned and fully lagged. END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings SPEED: 60 FPM, constant. BED: 7" x 1-1/2" x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30'. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: 2'-0" long zones pneumatically actuated. 1'-0" of live roller over end plates at each end of conveyor remains "live" during operation (# of zones x zone length + 2' = overall conveyor length). PNEUMATIC ACTUATION: Max'

196 Accumulator Variable Pressure Medium Duty Conveyor (196VP)

' TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S. RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196S, adjustable. BELTING: 2-1/4" wide "high strength" PVC-150 belt. *NOTE: WHEN SLAVE DRIVING OTHER UNITS, OPTIONAL 6" WIDE PVC-120 DRIVE BELT MUST BE USED ON UNITS 20' LONG AND ABOVE. CENTER DRIVE :Reversible drive with 24" integral belt take-up. For units under 8'-0" overall length, drive components must be stacked. Consult factory for minimum unit elevation. DRIVE PULLEY: 4" dia. with 1-3/16" dia. shaft or 8" dia. with 1-7/16" dia. shaft; both crowned and fully lagged. END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7" x 1-1/2" x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30'. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on la'

138 Accumulator Variable Pressure Light Duty Conveyor (138VP)

' TREAD ROLLERS: 1-3/8" dia. x 18 ga. galvanized steel, model 138G with 5/16" hex. PRESSURE ROLLERS: 1-3/8" dia. x 18 ga. galvanized steel, model 138G with 5/16" hex. RETURN ROLLERS: 1-3/8" dia. x 18 ga. galvanized steel, model 138G with 5/16" hex, adjustable. BELTING: 2-1/4" wide "high strength" PVC-150 belt. CENTER DRIVE: Reversible drive w/ 24" integral belt take-up. DRIVE PULLEY: 4" dia. with 1-3/16" dia. shaft or 8" dia. with 1-7/16" dia. shaft; both crowned and fully lagged. END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 6" x 1-1/2" x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30'. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional'