Contact us MX +52 (867) 715-5016

Line Shaft Conveyors

RBT3 3-Strand 90 Degree Round Belt Transfer Conveyor (138LR)

'TRANSFER ARM: 10 ga. formed channel. TRANSFER BELT: 3/8" dia. round polyurethane belt. LENGTHS: Transfer designed to mount in 796LS line shaft conveyors 15"-39" BF. BELT CENTERS: 12". ONE DIRECTION FLOW: Transfers product in one direction. TAKE-UP: Adjustable sheaves provides take-up of transfer belt. BEARINGS: Heavy duty, lubricated, ball bearing units with cast iron housings. BELT SPEED: Driven at 150% of speed as powered section transfer is mounted in. LIFT: 3/4" positive lift. MOTOR DRIVE: Optional. CAPACITY: 100 lbs. AIR CONTROLS: Air cylinder with single solenoid valve. FLOOR SUPPORTS: Optional'

796 Line Shaft Cross-Over Live Roller Conveyor (796LSX)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends or one end only. Specify where coupling required. BEARINGS: Precision, lubricated, ball bearing units with composite housings. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. SPEED: 60 FPM, constant. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. CROSS OVER DIRECTION: Specify "cross over to right hand" or "cross over to left hand". CAPACITY: 100 lbs. ELECTRICAL CONTROLS: Air cylinder with single solenoid valve.'

796 Line Shaft Live Roller Gate Module Conveyor (796LSG)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located on horizonal section only. LIFT: Gas cylinder provides assist for raising/lowering. BEARINGS: Precision, lubricated, ball bearing units with composite housings. BED: 4-1/2 " x 1-1/2" x 10 ga. formed steel channel frameon actual lift gate; 7" x 1-1/2" x 12 ga. on horizonal section. FLOOR SUPPORTS: Optional MOTOR DRIVE: Unit is designed to be driven by 796LS. SPECIFY HAND: Specify if gate is left or right hand.'

796 Line Shaft Live Roller Diverging Switch Conveyor (796LSDS)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC. BEARINGS: Precision, lubricated, ball bearing units with composite housings. SPEED: 60 FPM, constant. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional '

796 Line Shaft Converging Spur Live Roller Conveyor (796LSS)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved, 3" centers. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. NOTE: Spools in spur section only are keyed to provide positive drive (designed not to slip on drive shaft). COUPLINGS: Couplings located both ends or one end only. Specify where couplings required. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Short side of spur is always 12" overall length. FLOOR SUPPORTS: Optional. BEARINGS: Precision, lubricated, ball bearing units with composite housings. MOTOR DRIVE: Unit is designed to be driven by 796LS. ROLLER CHAIN: Spur driven via crossover with No. 40 chain.'

796 Line Shaft Live Roller Conveyor (796LS)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports. SPEED: 60 FPM, constant. FLOOR SUPPORTS: Optional. BEARINGS: Precision, lubricated, ball bearing units with composite housings. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional. '

796 Line Shaft Live Roller Conveyor (796LS)

'TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports. SPEED: 60 FPM, constant. FLOOR SUPPORTS: Optional. BEARINGS: Precision, lubricated, ball bearing units with composite housings. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional.'

738 Line Shaft Live Roller Light Duty Curve Conveyor (738LSC)

'TREAD ROLLERS: 1.9" dia. to 1-3/8" dia. x 16 ga. tapered steel, model 138Tw/ 5/16" hex, grooved. DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 7.5 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft, located on inside radius. NOTE: Spools are keyed to provide positive drive (designed not to slip on drive shaft). COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). BEARINGS: Precision, lubricated, ball bearing units with composite housings. 6 bearings per 90 degree and 60 degree curve; 4 per 45 degree and 30 degree. UNIVERSAL JOINTS: 4 per 90 degree and 60 degree curve; 2 per 45 degree and 30 degree curve. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. TANGENTS: 1'-0" both ends on 60 degree and 90 degree; 1'-6" both ends on 30 degree and 45 degree. 1'-0" infeed, 1'-0" discharge and no center tangent on 180 degree. Tangent roller centers 3" RC. FLOOR SUPPORTS: Optional MOTOR DRIVE: Unit is designed to be driven by 738LS. ELECTRICAL CONTROLS: Optional. '

738 Line Shaft Live Roller Light Duty Conveyor (738LS)

'TREAD ROLLERS: 1-3/8" dia. x 18 ga. galvanized steel, model 138G w/ 5/16" hex, grooved. DRIVE BELT: 1/8" dia., polyurethane belts. Nominal 10 lbs. per roller drive. DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D"). CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC. BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports. SPEED: 60 FPM, constant. FLOOR SUPPORTS: Optional. BEARINGS: Precision, lubricated, ball bearing units with composite housings. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base. ELECTRICAL CONTROLS: Optional.'

''