Accumulation Conveyors
138 Accumulator Variable Pressure Light Duty Conveyor-(138VP)
TREAD ROLLERS: 1-3/8″ dia. x 18 ga. galvanized steel, model 138G with 5/16″ hex.
PRESSURE ROLLERS: 1-3/8″ dia. x 18 ga. galvanized steel, model 138G with 5/16″ hex.
RETURN ROLLERS: 1-3/8″ dia. x 18 ga. galvanized steel, model 138G with 5/16″ hex, adjustable.
BELTING: 2-1/4″ wide “high strength” PVC-150 belt.
CENTER DRIVE: Reversible drive w/ 24″ integral belt take-up.
DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.
END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
SPEED: 60 FPM, constant.
BED: 6″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional
192 Accumulator SZ Chain Driven Zero Pressure Medium Duty Conveyor
TREAD ROLLERS: 1.9″ dia. x 12 ga., model 192S.
CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain.
CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor.
CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units.
ROLLER CENTERS: 4″ or 6″ RC ONLY.
SPEED: 35 FPM, constant.
ACCUMULATION ZONE: 5′-0″ zone lengths, zone singulation operation, photo electric sensor controlled zones with air clutch (60 psi max).
BED: 6-1/2″ x 1-1/2″ x 10 ga. and 4-1/2″ x 1-1/2″ x 10 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports.
FLOOR SUPPORTS: Optional
BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal.
FRL: Unit is provided with filter, regulator and lubricator with 3/8″ ports for 60 PSI operational pressure.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 300 lbs./ft. up to a maximum of 1200 lb. pallet load.
ELECTRICAL CONTROLS: Optional
196 Accumulator Smart Zone Zero Pressure Medium Duty Conveyor
TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.
PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt.
RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.
BELTING: 6″ wide black PVC-120 COS.
DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.
END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
SPEED: 60 FPM, constant.
BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
ACCUMULATION: Zone singulation operation; 3″ RC = 2′-0″ long zones; 4-1/2″ RC = 3′-0″ long zones. 1′-0″ of live roller at each end of conveyor over end plates remains “live” during operation. Zones are pneumatically actuated using photo electric sensors.
NEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.
FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports.
ELECTRICAL CONTROLS: Optional
196 Accumulator Variable Pressure Medium Duty Conveyor
TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.
PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.
RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.
BELTING: 2-1/4″ wide “high strength” PVC-150 belt. *NOTE: WHEN SLAVE DRIVING OTHER UNITS, OPTIONAL 6″ WIDE PVC-120 DRIVE BELT MUST BE USED ON UNITS 20′ LONG AND ABOVE.
CENTER DRIVE: Reversible drive with 24″ integral belt take-up. For units under 8′-0″ overall length, drive components must be stacked. Consult factory for minimum unit elevation.
DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.
END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
SPEED: 60 FPM, constant.
BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional
196 Accumulator Zero Pressure Medium Duty Conveyor
TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.
PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt.
RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.
BELTING: 6″ wide black PVC-120 COS.
DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.
END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
SPEED: 60 FPM, constant.
BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
ACCUMULATION: 2′-0″ long zones pneumatically actuated. 1′-0″ of live roller over end plates at each end of conveyor remains “live” during operation (# of zones x zone length + 2′ = overall conveyor length).
PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.
FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports.
ELECTRICAL CONTROLS: Optional
251 Accumulator Smart Zone Zero Pressure Heavy Duty Conveyor
TREAD ROLLERS: 2.5″ dia. x 11 ga. steel, model 251S.
PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 27″ BF for all widths.
BELTING: 12″ wide black PVC-120.COS.
SIDE MOUNT END DRIVE: Allows one direction unit operation.
DRIVE PULLEY: 12″ dia., with 1-15/16″ dia. shaft, crowned and fully lagged.
TAIL PULLEY: 8″ dia. with 1-3/16″ dia. shaft, crowned.
RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.
BED: 5 ” x 1-1/2″ x 3/16″ formed steel channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
SPEED: 35 FPM, constant.
ACCUMULATION: 5′-0″ long zones with zone singulation operation. 1′-6″ of live roller over end plates at each end of conveyor remains “live” during operation (# of zones x zone length + 3″-0″ + overall conveyor length). Zones are pneumatically actuated by using photo electric sensors.
FRL: Unit is provided with filter, regulator, lubricator with 3/8 ” ports for 60 PSI operational pressure.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: No. 60 chain provided at drive pulley. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional
251 Accumulator SZ Chain Driven Zero Pressure Heavy Duty Conveyor
TREAD ROLLERS: 2.5 ” dia. x 11 ga., model 251S.
CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain.
CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor.
CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units.
ROLLER CENTERS: 4″ or 6″ RC ONLY.
SPEED: 35 FPM, constant.
ACCUMULATION ZONE: 5′-0″ zone lengths, zone singulation operation, photo electric sensor controlled zones with air clutch (60 psi max).
BED: 7-1/2″ x 1-1/2″ x 7 ga. and 5 ” x 1-1/2″ x 7 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports.
FLOOR SUPPORTS: Optional
BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal.
FRL: Unit is provided with filter, regulator and lubricator with 3/8″ ports for 60 PSI operational pressure.
MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 1000 lbs./ft. up to a maximum of 3000 lb. pallet load.
ELECTRICAL CONTROLS: Optional
796 Accumulator Line Shaft Zero Pressure Conveyor
TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16″ dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1″ dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type “A”), one end only (type “B” or “C”) or none (type “D”).
CENTER DRIVE: Located approximately 16-1/2″ from end of bed section on 4″ RC; 18″ on 3″ and 6″ RC.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
ACCUMULATION: 2′-0″ zone length, pneumatically actuated, zone singulation operation.
SPEED: 60 FPM, constant.
BED: 7″ x 1-1/2″ x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.
FLOOR SUPPORTS: Optional
FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports.
PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional
796 Accumulator Smart Zone Line Shaft Zero Pressure Conveyor
TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16″ dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1″ dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type “A”), one end only (type “B” or “C”) or none (type “D”).
CENTER DRIVE: Located approximately 16-1/2″ from end of bed section on 4″ RC; 18″ on 3″ and 6″ RC.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
ACCUMULATION: Zone singulation operation; 2′-0″ zone length, photoeye controlled.
SPEED: 60 FPM, constant.
BED: 7″ x 1-1/2″ x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional