Line Shaft Conveyors

738 Line Shaft Live Roller Light Duty Conveyor (738LS)



TREAD ROLLERS: 1-3/8" dia. x 18 ga. galvanized steel, model 138G w/ 5/16" hex, grooved.
DRIVE BELT: 1/8" dia., polyurethane belts. Nominal 10 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").
CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports.
SPEED: 60 FPM, constant.
FLOOR SUPPORTS: Optional.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional.


738 Line Shaft Live Roller Light Duty Curve Conveyor (738LSC)



TREAD ROLLERS: 1.9" dia. to 1-3/8" dia. x 16 ga. tapered steel, model 138Tw/ 5/16" hex, grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 7.5 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft, located on inside radius. NOTE: Spools are keyed to provide positive drive (designed not to slip on drive shaft).
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").
BEARINGS: Precision, lubricated, ball bearing units with composite housings. 6 bearings per 90 degree and 60 degree curve; 4 per 45 degree and 30 degree.
UNIVERSAL JOINTS: 4 per 90 degree and 60 degree curve; 2 per 45 degree and 30 degree curve.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame.
TANGENTS: 1'-0" both ends on 60 degree and 90 degree; 1'-6" both ends on 30 degree and 45 degree. 1'-0" infeed, 1'-0" discharge and no center tangent on 180 degree. Tangent roller centers 3" RC.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: Unit is designed to be driven by 738LS.
ELECTRICAL CONTROLS: Optional.


796 Line Shaft Converging Spur Live Roller Conveyor (796LSS)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved, 3" centers.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. NOTE: Spools in spur section only are keyed to provide positive drive (designed not to slip on drive shaft).
COUPLINGS: Couplings located both ends or one end only. Specify where couplings required.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Short side of spur is always 12" overall length.
FLOOR SUPPORTS: Optional.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
MOTOR DRIVE: Unit is designed to be driven by 796LS.
ROLLER CHAIN: Spur driven via crossover with No. 40 chain.


796 Line Shaft Cross-Over Live Roller Conveyor (796LSX)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends or one end only. Specify where coupling required.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame.
SPEED: 60 FPM, constant.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CROSS OVER DIRECTION: Specify "cross over to right hand" or "cross over to left hand".
CAPACITY: 100 lbs.
ELECTRICAL CONTROLS: Air cylinder with single solenoid valve.


796 Line Shaft Live Roller Conveyor (796LS)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").
CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports.
SPEED: 60 FPM, constant.
FLOOR SUPPORTS: Optional.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional.


796 Line Shaft Live Roller Curve Conveyor (796LSC)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft, located on inside radius.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ELECTRICAL CONTROLS: Optional


796 Line Shaft Live Roller Diverging Switch Conveyor (796LSDS)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").
CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
SPEED: 60 FPM, constant.
BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional


796 Line Shaft Live Roller Gate Module Conveyor (796LSG)



TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located on horizonal section only.
LIFT: Gas cylinder provides assist for raising/lowering.
BEARINGS: Precision, lubricated, ball bearing units with composite housings.
BED: 4-1/2 " x 1-1/2" x 10 ga. formed steel channel frameon actual lift gate; 7" x 1-1/2" x 12 ga. on horizonal section.
FLOOR SUPPORTS: Optional
MOTOR DRIVE: Unit is designed to be driven by 796LS.
SPECIFY HAND: Specify if gate is left or right hand.


RBT3 3-Strand 90 Degree Round Belt Transfer Conveyor (138LR)



TRANSFER ARM: 10 ga. formed channel.
TRANSFER BELT: 3/8" dia. round polyurethane belt.
LENGTHS: Transfer designed to mount in 796LS line shaft conveyors 15"-39" BF.
BELT CENTERS: 12".
ONE DIRECTION FLOW: Transfers product in one direction.
TAKE-UP: Adjustable sheaves provides take-up of transfer belt.
BEARINGS: Heavy duty, lubricated, ball bearing units with cast iron housings.
BELT SPEED: Driven at 150% of speed as powered section transfer is mounted in.
LIFT: 3/4" positive lift.
MOTOR DRIVE: Optional.
CAPACITY: 100 lbs.
AIR CONTROLS: Air cylinder with single solenoid valve.
FLOOR SUPPORTS: Optional
NOTE: Specify twist (clockwise or counter clockwise) for drive bands on line shaft conveyor (model LS or LSA) that transfer mounts in. Consult factory.