Miscellaneous Conveyors
608sl Heavy Duty Slat Conveyor (608SL)
SLAT: 5-3/4″ wide formed 7 ga. steel channel.
DRIVE: End side mount drive.
SPEED: 35 FPM, constant (maximum).
TAKE-UP: Screw type.
BED: 19-3/4″ deep formed steel channel.
FLOOR SUPPORTS: Supports for elevations of 20″ to 26-1/4″ will be fixed height supports. Above 26-1/4″, standard SH supports will be used.
MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Chain sizes will vary with length of conveyor.
ELECTRICAL CONTROLS: Optional
700SBW Wire Mesh Belt Conveyor
BELTING: 1/2″ x 1″ x 11 ga. clinched edge, galvanized wire mesh belt.
DRIVE SPROCKETS: 4″ dia. sprocket with 1-3/16″ dia. shaft or 8″ dia. sprocket with 1-7/16″ dia. shaft.
TAIL SPROCKETS: 4″ dia. sprocket with 1-3/16″ dia. shaft.
END DRIVE: One-direction unit operation.
TAKE-UP: Screw type unit at tail end provides 12″ belt take-up.
RETURN ROLLERS: 1.9″ dia. x 16ga. steel, model 196S, adjustable.
BED: 7″ x 1-1/2″ x 10 ga. formed channel frame with UHMW wear strips.
FLOOR SUPPORTS: Optional.
BEARINGS: Drive and tail shaft bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
BELT SPEED: 60 FPM, constant.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.
700SBW Wire Mesh Belt Conveyor (CVC Conveyor Z Flow and C Flow)
CAPACIDAD: Más de 4000 lbs.
MARCO: Construcción tubular de alta resistencia.
UNIDAD: (4) cadenas de rodillos continuos accionadas por un motor de freno del tamaño requerido.
RITMO: Más de 25 cargas por minute.
VELOCIDAD: 60 FPM (100 FPM máximo).
CARGA: La carga automática se consigue midiendo la banda. No es necesaria la supervisión de ningún operador.
PLATAFORMA: El tamaño dependerá de cada producto.
PROTECTORES: Hechos de metal de protección.
CONTROLES: Según sean requeridos.
CD280 2-Strand Chain Drag Conveyor
FRAME: 7 ga. formed boxed channel.
CARRIER CHAIN: No. 80 (model CD280) or no. 60 (model CD260) riveted roller chain.
WEAR STRIP: UHMW long lasting wear strip, upper and lower.
CHAIN CENTERS: 18″
CHAIN TAKE-UP: Screw type located at tail end.
END DRIVE: Allows one-direction (unit) operation; add optional center drive for reversible application.
CHAIN SPEED: 35 FPM constant.
BEARINGS: Heavy duty, lubricated, ball bearing unit with cast iron housings.
CAPACITY: Unit load not to exceed 3000 lbs.
FLOOR SUPPORTS: Optional.
MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ELECTRICAL CONTROLS: Optional
PC-F Parts Conveyor With Feeder
BELTING: 3-ply black nitrile belt or 1/2″ x 1″ flat wire mesh belt with 1-1/2″ high galvanized cleats on 12″ centers.
DRIVE PULLEY: 4″ dia., with 1-3/16″ dia. shaft, fully lagged with nitrile belt; 4″ dia. sprockets supplied with flat wire mesh belt.
TAIL PULLEY: 4″ dia. with 1-3/16″ dia. shaft.
TAKE-UP: Screw type unit at tail pulley provides 12″ belt take-up.
BED: 8″ deep x 12 ga. enclosed box type construction with 14 ga. steel belt return pan.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
BELT SPEED: 35 FPM, constant.
MINIMUM PARTS SIZE: 1/2″ cube for nitrile belt, 1″ cube for flat wire mesh belt.
INCLINE: 30, 36 and 45 degree (specify).
PORTABLE SUPPORT: Adjustable floor support with 4″ dia. casters and bracing.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 350 lbs. total distributed load.
ROLLER CHAIN: No. 50 chain provided at drive pulley. Chain take-up provided on motor base.
ELECTRICAL CONTROLS: Optional
IPT Indexing Powered Turntable Heavy Duty Conveyor (IPT)
ROTATION: 2 position, 3 position or 4 position.
SPEED: 35 FPM at outside diameter.
CHAIN DRIVE: No. 80 roller chain.
CHAIN GUARD: The chain drive is completely enclosed.
CASTERS: (8) 4″ dia. heavy duty rubber-covered casters support rotation of turntable carrier platform.
DIAMETER: 3′-0″, 3′-6″, 4′-0″, 4′-6″, 5′-0″, 5′-6″, 6′-0″, 6′-6″, 7′-0″, 7′-6″ and 8′-0″ dia.
CARRIER PLATFORM: 3″ structural platform with 1/2″ thick steel plate supported by heavy duty casters.
BEARINGS: Heavy duty ball bearing 4-hole flange.
CAPACITY: 4000 lbs. max. product load.
MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor with brake.
ELEVATION: Minimum 12-1/2″ to top of plate with (4) structural leveling supports.
ELECTRICAL CONTROLS: Limit switches supplied as follows: 2 position = 2 limit switches; 3 position = 3 limit switches; 4 position = 4 limit switches.
Pc Parts Conveyor (PC)
BELTING: 3-ply black nitrile belt with 1-1/2″ high molded cleats on 12″ centers; 1/2″ x 1″ flat wire mesh belt with 1-1/2″ high galv. cleats on 12″ centers. NOTE: Units with 6″ wide belt not available with wire mesh belt.
DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft, crowned and fully lagged.
TAIL PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.
BELT RETURN: Formed steel slide retains belt and cleats inside bed.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
BELT SPEED: 60 FPM, constant.
BED: 7″ deep x 12 ga. one piece formed box-type construction.
TAKE-UP: Screw type unit at tail pulley provides 12″ belt take-up.
PORTABLE SUPPORT: 4″ dia. casters, tubular construction, adjustable both ends.
GUARD RAILS: 3-1/2″ high x 12 ga. formed steel with gate at infeed.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 330 lbs. total distributed live load at 60 FPM.
ELECTRICAL CONTROLS: Optional
SD60 Skewed Wheel Diverter Conveyor (SD60))
BELTS: 1/4″ dia. round polyurethane.
DRIVE WHEELS: 2-1/2″ O.D. x 3/4″ face polyurethane, quantity as required, driven by 1/4″ dia. polyurethane belts.
DRIVE SHAFT: 1-3/16″ dia.
AIR CYLINDER: Double action.
AIR CONTROLS: Single solenoid valve.
FRAME ASSEMBLY: Designed to mount into 196LR, 196CALR and 196LS line shaft driven conveyor.
DIVERSION ANGLE: 30 degree, 45 degree and 90 degree. Guard rails on take-away spur conveyor may be required at various angles.
BEARINGS: Heavy duty, lubricated, ball bearing unit with cast iron housings.
RATE: Up to 60 sorts per minute.
SPEED: 60-180 FPM, constant. Other speeds available. Consult factory.
MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 50 lbs. per ft.; maximum unit load not to exceed 150 lbs.
VBT3 3 Strand 90 Deg Transfer V belt Conveyor (WT3)
BRAZO DE TRANSFERENCIA: Canal de 10 ga.
BANDA DE TRANSFERENCIA: Sección «B» correa trapezoidal.
LONGITUDES STANDAR: 3′, 4′, 5′ 6′, 7′ y 8′.
CENTROS DE CARREAS TRAPEZOIDALEZ: 18″
UNIDAD CENTRAL: Permite el funcionamiento reversible de la unidad.
ASCENSOR: Tipo positivo.
VELOCIDAD DE BANDA: 35 FPM, constante.
RODAMIENTOS: Ruedas de precisión, de alta resistencia, lubricadas con hierro fundido.
CAPACIDAD: La carga no debe exceder las 500 lbs.
SOPORTES DE PISO: Parte integral de la unidad, con capacidad de ajuste entre 18″ y 20″ de la parte superior de la correa trapezoidal (posición hacia abajo).
IMPULSOR DE MOTOR: Motor de engranaje de ángulo recto ODP. 60 ciclos. ½ HP, 230/460/3.
CONTROLES ELÉCTRICOS: Opcional.
WT3 3 Strand 90 Deg Transfer Skate Wheel Conveyor (WT3)
BRAZO DE TRANSFERENCIA: Canal de 7 ga.
RUEDAS DE TRANSFERENCIA: Frantz modelo 35Z en centros de rueda de 3. Las ruedas tienen una capacidad de 50 lbs.cada una.
LONGITUDES STANDARD: 2′, 3′, 4′, and 5′.
CENTRO DE TIRAS: 18″
UNIDAD CENTRAL: Permite el funcionamiento reversible de la unidad.
ASCENSOR: Tipo positivo
RODAMIENTOS: Ruedas de precisión, de alta resistencia, lubricadas con hierro fundido.
CAPACIDAD: La carga no debe exceder las 500 lbs.
MONTAJE: Parte integral de la unidad, con 15″ arriba de la elevación de la rueda (posición hacia abajo). Unidad diseñada para montarse entre los bastidores del transportador.
CONTROL DE: Cilindro de aire (doble acción) con una electro válvula.